欢迎光临
我们一直在努力

思科路由器设置界面 思科路由器设置ip

思科路由器设置界面

  思科路由器大家也习惯叫为Linksys路由器,是国内用户使用很多的路由器品牌。下面是小编整理的关于思科路由器英文版设置,欢迎大家参考!

  思科路由器进入管理界面方法:

  1、先查看IP,方法:win+r—输入:cmd—在再黑白界面输入:ipconfig,按回车

  2、根据网关查看路由器地址。若网关与路由器的ip一般是相同的

  3、在IE地址栏中输入地址:192.168.1.1

  4、弹出路由器登陆界面输入路由器的默认登陆用户名:admin 密码:admin(如果不正确,就看路由器背面)。

  思科路由器中英文翻译

  System summary(系统总结)

  The System Summary screen displays the router's current status and settings. This information is read only. If you click the button with underline, it will hyperlink to related setup pages. On the right side of the screen and all other screens in the Utility will be a link to the Site Map, which has links to all of the Utility's tabs.

  Serial Number: The serial number of the RV082 unit.

  System up time: The length of time in Days, Hours, and Minutes that the RV082 is active.

  Firmware version: The current version number of the firmware installed on this unit.

  CPU: The type of the RV082 processor. It is Intel IXP425.

  DRAM: The size of DRAM on the board. It is 32MB.

  Flash: The size of Flash on the board. It is 16MB.

  Configuration: If you need guideline to re-configure the router, you may launch Wizard.

  Port Statistics: Users can click the port number from port diagram to see the status of the selected port

  该系统总的屏幕显示路由器的当前状态和设置。此信息是只读的。如果您按一下按钮,与强调,将相关的设置超链接的网页。论屏幕和实用工具的所有其他屏幕右侧将是一个网站地图,它的效用的标签各个环节的联系。

  编号:该RV082单位的序列号。

  系统时间:在几天,几小时的时间长度,及记录的RV082处于活动状态。

  固件版本:对本单位安装的固件的版本号。

  处理器:RV082的处理器类型。这是英特尔IXP425。

  内存:内存上的电路板尺寸。这是32MB。

  快讯:在闪存上的电路板尺寸。这是16MB的。

  配置:如果您需要的指引,重新配置路由器,您可能会启动向导。

  港口统计:用户可以从港口图单击端口编号,以查看选定的端口的状态

  setup(设置)

  The Setup screen contains all of the router's basic setup functions. The device can be used in most network settings without changing any of the default values. Some users may need to enter additional information in order to connect to the Internet through an ISP (Internet Service Provider) or broadband (DSL, cable modem) carrier.

  Host Name & Domain Name:

  Enter a host and domain name for the Router. Some ISPs (Internet Service Providers) may require these names as identification, and these settings can be obtained from your ISP. In most cases, leaving these fields blank will work.

  LAN Setting:

  This is the Router's LAN IP Address and Subnet Mask. The default value is 192.168.1.1 for IP address and 255.255.255.0 for the Subnet Mask.

  安装屏幕包含路由器的基本设置的`所有功能。该器件可用于在大多数网络设置,在不改变默认的任何值。有些用户可能需要输入更多的信息,以便连接到互联网,通过一个ISP(互联网服务提供商)或宽带(DSL,电缆调制解调器)承运人。

  主机名和域名:

  输入一个路由器的主机和域名。有些ISP(互联网服务提供商)可能需要这些名称作为识别,这些设置可以从ISP获得的。在大多数情况下,这些领域留下空白的工作。

  局域网设置:

  这是路由器的局域网IP地址和子网掩码。默认值是IP地址和子网掩码255.255.255.0 192.168.1.1

  DHCP(动态主机配置协议)

  The Router can be used as a DHCP (Dynamic Host Configuration Protocol) server on your network. A DHCP server assigns available IP addresses to each computer on your network automatically

  该路由器可以作为DHCP(动态主机配置协议)您的网络服务器上。一个DHCP服务器分配网络上可用的IP地址给每台电脑自动

  System management(系统管理)

  There are two functions provided for users – Smart Link Backup and Load Balance. If users select DMZ in setup page, users could not do the Dual WAN setting here.

  If Load Balance (Auto Mode) is selected, it will be automatically computing the max bandwidth of WAN1 and WAN2 by using Weighted Round Robin to balance the loading.

  Network Service Detection

  This tool can detect the network connection status of ISP by pinging Default Gateway, ISP Host, Remote Host or DNS Lookup Host.

  Retry count: The count of ping. The default is 5.

  Retry timeout: The interval between two ping actions. The default is 30 seconds.

  When Fail:

  Generate the Error Condition in the System Log: The Router will generate the System Log when ping fail to inform users that the ISP connection is disconnected.

  Remove the Connection: This WAN Interface will be suspended when the network connection to ISP is not active. The traffic on this WAN will be dispatched to the other WAN port. Once ISP returns to c

  有两个功能,为用户提供-智能链路备份和负载平衡。如果用户选择非军事区的设置页,用户不能这样做的双WAN设置在这里。

  如果负载平衡(自动模式)的选择,它会自动计算采用加权循环,以平衡负载的WAN1和WAN2最大带宽。

  网络服务检测

  此工具可以检测到通过Ping默认网关,ISP的主机,远程主机或DNS查找主机的ISP网络的连接状态。

  重试计数:在平罪名。默认值为5。

  重试超时:两平的行动间隔。默认为30秒。

  当失败:

  生成系统日志中的错误条件:路由器将生成系统日志时,平没有通知的ISP连接的用户断开。

  删除连接:广域网接口,这将暂停使用时,网络连接到ISP并不活跃。关于这个广域网流量将被派往其他广域网端口。一旦返回到c的ISP

  port management (端口管理)

  In this router, users can configure the connection status for each port, such as Priority, Speed, Duplex, Auto-Negotiation and VLAN.

  Basic Per Port Config.

  Port ID: They are port 1~8, DMZ/Internet and Internet.

  Interface: They are LAN, WAN2 or DMZ, WAN1.

  Disable: Check the box, the port will be disabled. It is a per-port setting.

  Priority: Select High or Normal for Port-based QoS (Quality of Service). QoS is used to maximize a network’s performance and this setting allows you to prioritize performance on eight LAN ports.

  Speed: Users can manually config the per-port speed as 10Mbps or 100Mbps.

  Duplex: Users can manually config the per-port duplex as half-duplex or full-duplex.

  Auto-negotiation: Users can configure the per-port mode as Auto-negotiation, so Users will not need to setup speed and duplex.

  VLAN (Virtual LAN): A VLAN Group is a broadcast domain, and the stations on the same VLAN group can communicate with each other, and the stations on the separate VLAN groups

  在这种路由器,用户可以为每个如优先,速度,双工,自动协商和VLAN端口,配置的连接状态。

  每端口的基本配置。

  端口ID:他们是端口1〜8,非军事区/互联网和互联网。

  接口:他们是局域网,WAN2或DMZ,WAN1。

  禁用:检查中,该端口将被禁用。这是一个每个端口设置。

  优先级:选择高或普通的基于端口的QoS(服务质量)。服务质量是用来最大限度地提高网络的性能和此设置允许您在八个优先LAN端口的性能。

  速度:用户可以手动配置每个端口为10Mbps或100Mbps的速度。

  复式:用户可以手动配置的每一半端口全双工半双工或全双工。

  自动谈判:用户可以配置每个端口的模式,自动协商,让用户将不需要安装的速度和双工。

  VLAN(虚拟局域网):一个VLAN集团是一个广播域,并在同一VLAN组的车站可以相互沟通,并在不同的VLAN组的车站

  firewall (防火墙)

  From the Firewall Tab, you can configure the Router to deny or allow specific internal users from accessing the Internet. You can also configure the Router to deny or allow specific Internet users from accessing the internal servers. You can set up different packet filters for different users that are located on internal (LAN) side or external (WAN) side based on their IP addresses or their network Port number.

  Firewall

  The default is enabled. If users disable the Firewall function, SPI, DoS, Block WAN Request will be disabled, Remote Management will be enabled and Access Rules and Content Filter will be disabled.

  Stateful Packet Inspection (SPI)

  The Router's Firewall uses Stateful Packet Inspection to maintain connection information that passes through the firewall. It will inspect all packets based on the established connection, prior to passing the packets for processing through a higher protocol layer.

  Denial of Service (DoS)

  Protect internal networks from Internet att

  从防火墙选项卡,您可以配置路由器,拒绝或允许从互联网访问特定内部用户。您还可以配置路由器拒绝或允许访问内部服务器的特定互联网用户。您可以设置该位于内部(LAN)一方或外部(广域网)方根据其IP地址或端口号的网络不同用户的不同数据包筛选器。

  防火墙

  默认被启用。如果用户禁用防火墙功能,SPI和拒绝服务,座广域要求将被停用,远程管理将启用和访问规则和内容过滤器将被禁用。

  状态包检测(SPI)

  路由器的防火墙使用状态包检测技术来保持连接信息穿过防火墙。它将考察了已建立的连接的所有数据包,通过前处理的数据包通过一个更高的协议层。

  对拒绝服务(DoS)

  从互联网先进交通运输保护内部网络

  Protectlink(防护连接)

  Trend Micro™ ProtectLink Gateway is a hosted security service that stops spam and filters URLs

  to prevent unwanted content from passing through your Linksys router. ProtectLink stops over 97%

  of spam and controls access to Web sites based on the categories you select.

  More…

  I want to buy Trend Micro ProtectLink Gateway

  I have purchased ProtectLink Gateway and want to register it

  I have my Activation Code (AC) and want to activate ProtectLink Gateway

  趋势科技™ProtectLink网关是一项托管安全服务,停止垃圾邮件和过滤器的网址

  防止通过Linksys路由器通过不想要的内容。 ProtectLink停止超过97%

  垃圾邮件和控制获取有关您选择的类别为基础的网站。

  更多…

  我想购买趋势科技ProtectLink网关

  我已经购买ProtectLink网关,并希望将其注册

  我有我的激活代码(AC)和要激活ProtectLink网关

  VPN(虚拟专用网络) log(原本) wizard(向导)

  Support (支持) Logout (关闭)

【思科路由器设置界面】相关文章:

1.思科路由器设置

2.思科路由器设置VPDN的方法

3.思科路由器怎么设置「图解」

4.思科路由器怎么设置

5.思科路由器路由协议设置

6.思科LINKSYS 宽带无线路由器设置方法

7.思科路由器广域网协议设置

8.思科无线路由器的详细设置方法

评论 抢沙发

  • 昵称 (必填)
  • 邮箱 (必填)
  • 网址
赞(0) 打赏
分享到: 更多 (0)

轻博客

联系我们联系我们
'); })();